Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateFast, Reliable Garage Door Spring Repair Across Kent
A broken garage door spring in Kent usually makes itself known with a bang from the garage, and then the door won’t lift. If that’s where you are right now, call (877) 619-3963. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We know this city well, from the low-headroom single bays tucked under East Hill ramblers to the taller two-car garages in Panther Lake, and the call is free. Estimates are free too, and the price you agree to before any work starts is the price on the invoice. Springs are the most dangerous part of a garage door to touch. We take that seriously, and we handle them with the right equipment.
Why Kent Homeowners Call Burien Garage Door Repair for Garage Door Spring Repair
We’re a garage door specialist, nothing else. That focus matters in a city where the housing stock runs from the 1960s into the 2000s and a single street can hold both. A technician who spends every working day on doors and openers recognizes the failure modes of the equipment in front of them, rather than guessing at it.
Our technicians have up to 14 years of experience, and they’re trained on the brands most Kent garages actually run: LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman and Raynor. That means when we arrive, we already know what typically fails on your system. We don’t sell new doors. The job is getting your door back to working order. That’s the lane we stay in.
Kent calls come in from all over: the older ramblers up on East Hill, the subdivisions out toward Panther Lake and the Covington edge, and the valley neighborhoods near downtown. The drive is short from our primary service area in Burien, and we route Kent work efficiently so a spring failure doesn’t leave your car trapped all day. Call (877) 619-3963 for a free estimate.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Our Garage Door Spring Repair Services in Kent
Springs carry the full weight of the door. When one lets go, it’s not a door problem to leave for later. Here’s what we handle for Kent homeowners.
Torsion Spring Replacement
Most two-car doors in Kent run a torsion spring mounted on a shaft above the door, and it’s the part that takes the most cycles. When it snaps, the door becomes dead weight and the opener can’t safely lift it. We measure the broken spring against a replacement with the right cycle rating for the door’s weight and how often you use it, then check the drums, cables and end bearing plates while we’re up there. Call us and we’ll get you a written price before we start.

Extension Spring Replacement
Lots of the mid-century East Hill ramblers still run extension springs along the horizontal tracks, and many of those are original to the house. Extension springs stretch and lose tension over time, and older setups often went without a safety cable running through the spring. We replace them as a matched set, confirm the door is balanced, and fit the safety hardware these doors should have.

Broken Spring Repair
When a spring breaks, don’t run the opener. It’ll strain against a door it was never sized to lift. We diagnose which spring failed, whether the cables and track were affected, and whether the door is safe to operate. This is a repair, not a sales visit. You’ll get a straight answer on what failed and what it takes to fix it.

Spring Inspection
Springs wear quietly until they don’t. An inspection checks balance, cable condition, drum alignment and the springs themselves, and it’s how a lot of Kent homeowners find out a spring is near the end of its cycles before it strands a car in the driveway. If everything’s in good shape, we’ll tell you that too. If you want a look before something breaks, our garage door spring repair team can put eyes on it.
Trusted Brands We Service in Kent
The doors and openers we work on most are LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman and Raynor. On the opener side that covers everything from older Craftsman and Genie chain drives to modern LiftMaster and Chamberlain smart-home systems. On the door side it means we know how a Clopay or Amarr sectional is built and what wears first. We don’t stock parts locally or carry a warehouse, so we source what your specific system needs and schedule the work around it. Familiarity with the brand cuts down on guesswork once we’re at your Kent home.
Common Garage Door Spring Repair Problems We See in Kent Homes
- Corroded tracks and hinges from Puget Sound rain. Kent’s damp, wet winters rust steel tracks and hinges, which throws off track alignment and door balance. A door that drifts or binds wears its springs unevenly, and uneven springs snap early, especially on the older doors up on East Hill.
- Legacy extension springs and one-piece hardware past their service life. The 1960s-70s ramblers around Kent often still run original extension spring setups, and parts for that hardware take real hunting to source. That forces an honest repair-versus-retrofit decision rather than a simple swap.
- Moisture-swollen wood panels that bind. Wood doors soak up the damp here and swell, adding load the springs and opener rail were never sized for. The door drags, the opener works harder, and spring cycles burn off faster.
- Builder-grade sectional springs at end of life. The 1990s-2000s subdivisions around Panther Lake and the 98042 edge have plenty of steel sectional doors now 20 to 40 years old, and their springs are simply at the end of their cycles. That’s a straightforward torsion replacement, not a retrofit.
How a Spring Repair Usually Goes in Kent
A spring failure in Kent tends to announce itself at the worst possible moment: a loud bang from the garage, a door that won’t budge, or an opener that strains to lift a 150-to-350-pound door because the torsion or extension spring is no longer carrying the load. On damp East Hill ramblers, the same call often turns up rusted steel tracks, moisture-swollen wood panels that bind, and 30- to 40-year-old builder-grade hardware whose legacy parts take hunting down. On 1990s-2000s Panther Lake and 98042 sectional doors, the springs are usually just at the end of their spring cycles.
A qualified local pro checks door balance, cables, drums and end bearing plates, measures the old spring against a replacement with the right cycle rating, confirms track alignment and the weather seal, and only recommends a retrofit-to-torsion or a full opener and rail upgrade when the existing hardware can’t be safely re-sprung. That last part is where Kent separates itself. On the mid-century East Hill ramblers, the garage is often a tight single-car bay tucked under the main roofline with low headroom. Legacy one-piece doors and their extension spring setups frequently can’t accept a standard torsion conversion without custom low-headroom drums and end bearing plates. The tall two-car bays in Panther Lake and the newer subdivisions never force that. It’s a call we can make once we see the door, and it’s the difference between a straight spring replacement and a retrofit.
See the difference
Before
After
Before
After
Before
AfterPricing for Garage Door Spring Repair in Kent, WA
For one spring, spring repair in Kent typically runs $180 – $340. A matched pair is usually replaced together, so a pair costs about twice that. Below are the typical estimated ranges for the work we do most often. The written estimate sets the final price, and we quote and agree on it before any work starts, so you’re never looking at an invoice bigger than the number you said yes to.
| Service | Typical Estimated Range |
|---|---|
| Spring Repair (one spring) | $180 – $340 |
| Cable Repair | $130 – $250 |
| Opener Repair | $120 – $320 |
| Opener Installation | $250 – $550 |
| Track Realignment | $120 – $240 |
| Roller Replacement | $110 – $220 |
| Panel Replacement | $250 – $500 |
What moves the number: whether it’s one spring or a pair, the door’s weight and cycle rating, whether the cables, drums or tracks were affected, and on the older East Hill doors, whether the existing hardware can be re-sprung at all or needs a retrofit. Call (877) 619-3963 for an exact quote. Estimates are free.
We Also Serve Cities Near Kent
Kent sits in the middle of our South King County coverage, and we take calls from the surrounding towns too. If you’re in Des Moines, SeaTac, Tukwila or Renton and your door won’t lift, we can help. The same brand knowledge and the same upfront written pricing apply. Find more on our Kent page if you want to see how we work across the area.
Serving Kent, WA – Our Local Coverage Area
We serve Kent and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Garage Door Spring Repair in Kent
Sometimes yes, sometimes it needs custom low-headroom drums and end bearing plates first. The tight single bays under the roofline on mid-century East Hill homes don’t have the clearance a standard torsion conversion needs, so it depends on the actual headroom and door. We measure it on site and tell you honestly whether a conversion is worth it or whether a fresh extension spring setup is the smarter repair. Call (877) 619-3963 for a free estimate.
It comes down to whether the existing hardware can be safely re-sprung. If the tracks, cables and end plates are sound, a straight spring replacement is usually the answer. If the door is a legacy one-piece or the hardware can’t be sourced or safely loaded, that’s when retrofit-to-torsion or a bigger upgrade makes sense. We check before we recommend. Estimates are free.
Often, yes. When a spring stops carrying its share of the door’s weight, the opener strains to lift the whole door, which it was never built to do. Stop running it and get it checked, because a straining opener can burn out the motor and the door can drop. Call (877) 619-3963 and we’ll diagnose it.
The spring that matches the door’s actual weight and cycle rating, not just whatever is on there now. We measure the old spring against a replacement with the right cycle rating for your door and how often you use it. Guessing at it wears the door and opener faster. Call for a free estimate.
Because of the rain. Kent’s damp Puget Sound climate rusts steel tracks and hinges, which throws off alignment and balance, and it swells wood panels so they bind in the tracks. Both add load the springs and opener were never sized for, which wears springs faster. Call (877) 619-3963 and we’ll check yours.
Get Your Kent Garage Door Back to Working Order
If your door won’t lift or you heard that bang, it’s a spring problem, and it’s worth fixing right rather than running the opener against it. Call (877) 619-3963 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We quote and agree on the price before any work starts, and we work on your brand.
Written by the team at Burien Garage Door Repair.